Laserfiche WebLink
PLOT PLAN REQUIREMENT <br /> A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to <br /> scale,in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing,if one is used.The plot plan drawing shall <br /> be on letter or legal size paper with Horth being at the top of the page. (Make sure all relevant items below are shown—check <br /> eclat relevant hos): <br /> • Property lines,road right-of-ways,and road centerlines including dis:ances to properly lines,road right-of-ways and road <br /> centerlines for all existing and proposed structures on the parcel <br /> ❑ Ordinary High Water Mark(OHWM)when existing,and distances to it from all existing and proposed structures <br /> u Provide Total Impervious Surface(IS)Percentages including new existing and proposed development.This standard is only <br /> applicable if I hr proposed project is within 3e0'of the OHWM of any body of water. You only need to count the impervious <br /> surfaces that arc partially or entirely within 300'of the OIIWM of a body of water.To calculate,divide the total existing and <br /> proposed impervious surfaces in square feet by the total square footage of the parcel above the OHWM.Then multiply that number <br /> by 100 to get a percentage.Example:2,500 square feel of IS within 300'of OHWM_43,560 square foot parcel x 100= 5.74% <br /> impervious surfaces(1 acre=43.5600 square feet).Impervious surfaces include but are not limited to:building roofs,sidewalks, <br /> decks,patios,ccnicnt/asphaltIgravcl driveways,etc.If the proposed project exceeds 15%impervious surface,mitigation is required. <br /> If the impervious surface exceeds 30%,you will need to apply for a variance.NOTE:If you are only replacing existing legally <br /> built structures within the same footprint,no impervious surface calculations are needed.Land Services reserves the right to <br /> require a survey when there arc disputes over this calculation. <br /> ❑ Floodplain and wetland areas'bou-tdaries and distances to them from al:exist-ng and pmposed structures <br /> U Existing enc proposed srue:ures on the parcel:nclud.ng all decks/porches/walkways/etc;must show dimensions for ALL items <br /> ❑ Existing and proposed sanitary system and wel'brat ons including distances to existing and proposed structures <br /> O Heights kr all existing and proposed structures NOTE:Heigtt is measured from lowest adjacent grade to the highest roof peak <br /> ❑ (CotnmcrciaL+Industrial Only)Existing and pi-mused parking;must show dimensions and proposed number of stalls <br /> • Existing and proposed driveways;must shcw dimensions and width NO•I E:Driveways must have a cleared width of 20 ft and a <br /> cleared height oT I'i n,and sufficient tum-around spare for rescue services to utilize <br /> ❑ North arrow <br /> ❑ Vegetation proposed to be removed or disturbed <br /> ❑ Location and extent of proposed filling/grading <br /> ❑ Location and type of erosion control measures <br /> O Construction plans shall be submitted with this application for all Commcreial(Indnstrial related construction. <br /> Construction plans shall show interior layout,exterior profiles and exterior heights. <br /> © Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining <br /> walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> U If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the applicant. <br /> Page 2 of 4 <br /> Burnett County,WI Land Use Application-Rev 12!2020 <br />