2021/10/12 - LAND USE - LUP - Dwelling/Principle Building - Single Family - LUP-21-649

Home Browse Search

PLOT PLAN REQUIREMENT A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to scale,in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing,if one is used.The plot plan drawing shall be on letter or legal size paper with North being at the top of the page. (Make sure all relevant items below are shown-check each relevant box): ✓ ✓ 1/ Property lines,road right-of-ways,and road centerlines including distances to property lines,road right-of-ways and road centerlines for all existing and proposed structures on the parcel "Ordinary High Water Mark(OHWM)when existing,and distances to it from all existing and proposed structures ❑ Provide Total Impervious Surface(IS)Percentages including new existing and proposed development.This standard is only applicable if the proposed project is within 300'of the OHWM of any body of water. You only need to count the impervious 'surfaces that are partially or entirely within 300' of the OHWM of a body of water. To calculate,divide the total existing and A) proposed impervious surfaces in square feet by the total square footage of the parcel above the OHWM.Then multiply that number 1_ by 100 to get a percentage.Example:2,500 square feet of IS within 300'of OHWM=43,560 square foot parcel x 100= 5.74% impervious surfaces(1 acre=43,560 square feet).Impervious surfaces include but are not limited to:building roofs,sidewalks, decks,patios,cement/asphalt/gravel driveways,etc.If the proposed project exceeds 15%impervious surface,mitigation is required. If the impervious surface exceeds 30%,you will need to apply for a variance.NOTE: If you are only replacing existing legally built structures within the same footprint,no impervious surface calculations are needed. Land Services reserves the right to require a survey when there are disputes over this calculation. Floodplain and wetland areas/boundaries and distances to them from all existing and proposed structures xis ing andproposed struc es on the par el i udin all decks/porches/walkways/etc;must show dimensions for ALL items G A , 3x3.( OA/ 4 "Existing and proposed sanitary system and wel locations including distances to existing and pr posed structures U Heights f all existi nd p o ose stru4ctures NOT? 1eight ism sjred om lowest adjacent grade to the highest roof peak #4-91^1 i D C9�N' tr , qtli (Coimercial/Indu t al lnly)Ex s ing and proposed parkin;muss?ihi imensions and proposed number of stalls xistin and ro osed drivewa s; must show dimensions and width NOTE: Driveways must have a cleared width of 20 ft and a g P P Y � Y cleared height of 13 ft,and sufficient turn-around space for rescue services to utilize worth arrow /I vegetation proposed to be removed or disturbed - U at.,•LrwIIS h 5msffi tv4u i , re . Na��« Pim O—Location and extent of proposed filling/grading I 2,/l s 47/ f-" / u', des- e.:.0�j,,�r g4fary ❑ Location and type of erosion control measures , construction plans shall be submitted with this application for all Commercial/Industrial related construction. V'� - Construction plans shall show interior layout,exterior profiles and exterior heights. L13• Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. V.-1i all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be issued and may be returned to the applicant. Page 2 of 4 Burnett County, WI Land Use Application- Rev 12/2020