Laserfiche WebLink
PLOT PLAN REOUIREMENT <br /> A plot plan drawing is required to be ittbriliftttf along itb this application. The plot plan drawing shall either be drawn to <br /> scale,in feet,or be FULLY dimensioned in feet. Please note the sante on the drawing.it one is used.The plot plan drawing shall <br /> be on letter or legal size paper with North being at the top of the page. (Make sure all relevant items below are shown—check <br /> each"demist box); <br /> :1 Property lines.,road rien-of-ways.and road centerlines including distances.to property lines-road right-of-ways and road <br /> centerlines for all existing and proposed structures on the parcel <br /> L:1 Ordinary High Water Mark(OHWM)when existing,and distances to it from all existing and proposed structures <br /> O Provide Total Impervious Surface(IS)Percentages int:Iodine new existing and proposed development.This standard is only <br /> applicable lithe proposed project is within 300'of the ORWM of any body of water. You only need to count the impervious <br /> surfaces that are partially or entirely within 300'of the 01-PWM of a body of water.To calculate.divide the total existing and <br /> proposed impervious surfaces in square feet by the total square footage of the parcel above the 011W/v1.Then multiply that number <br /> by 100 to get a percentage.Example:2,500 square feet of IS within 300'of OFIWM 43,560 square foot parcel x1410-- 5,74% <br /> impervious surfaces(I acre=43,5(,0 square feet).Impervious surfaces include but are not limited to:building roofs,sidewalks. <br /> decks,patios,cement asphaltlgravel driveways,etc. tithe proposind project exceeds 15%impervious surface,mitigation is required. <br /> If the impervious surface exceeds 30%,you will need to apply for a variance.NOTE:If you are only replacing existing legally <br /> built structures within the same footprint,no impervious sorface calculations are needed. Land Services reserves the right to <br /> require a survey when there are disputes over this calculation. <br /> 2 <br /> Floodplain and wetland areasibourxlarics and distances to them from all existing and proposed structures <br /> U Existing and proposed structures on the parcel including all decksiporchesilwalkwaysietc:must show dimensions for ALL items <br /> 2 Existing and proposed sanitary system and well locations including distances to existing and proposed structures <br /> O I leights for all existing and proposed structures NOTE: Height is measured from lowest adjacent grade to the highest roof peak <br /> 3 (Commercial/Industrial Only)Existing and proposed parting;must show dimensions and proposed number vistas <br /> • Existing and proposed driveways;must show dimensions and width NOTE:Driveways must have a cleared width of 20 ft and a <br /> cleared height of 13 ft.and sufficient turn-around space for rescue services to utilize <br /> • North arrow <br /> 2 Vegetation proposed to be removed or disturbed <br /> L-.1 Location and extent of proposed filling/grading <br /> • Location and type of erosion control measures <br /> ▪ Construction plans shall be submitted with this application for all Commercialfludustriai related construction. <br /> Construction plans shall show interior layout,exterior profiles and exterior heights. <br /> U Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining <br /> wails,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> • If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the appficant_ <br /> Page 2 of 4 <br /> Burnett County,WI Land Use Application —Rev 12/2020 <br />