Laserfiche WebLink
PLOT PLAN REQUIREMENT <br /> A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to <br /> scale,in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing,if one is used.The plot plan drawing shall <br /> be on letter or legal,size paper with North being at the top of the page. (Make sure all relevant items below are shown–check <br /> each relevant box): <br /> XProperty lines,road right-of-ways,and road centerlines including distances to property lines,road right-of-ways and road <br /> centerlines for all existing and proposed structures on the parcel <br /> ■ I •m.i • -i_ ater Mar I - •• • .• - - •• . -. - . • : . - . - . : . • • oposed struc-•. • <br /> o...-1pT t.t 1 \�.T <br /> - T itel Im ',,s „r <br /> cfacpercentages including new existing and proposed development.This standard is only <br /> —" <br /> applicable if the proposed project is withinany o y of water. Y ou onry ITEM coun t ie impervious <br /> surfaces that are partially or entirely within 300' of the OHWM of a body of water. To calculate,divide the total existing and <br /> proposed impervious surfaces in square feet by the total square footage of the parcel above the OHWM.Then multiply that number <br /> by 100 to get a percentage.Example: 2,500 square feet of IS within 300' of OHWM- 43,560 square foot parcel x 100= 5.74% <br /> impervious surfaces(1 acre=43,560 square feet).Impervious surfaces include but are not limited to:building roofs, sidewalks, <br /> decks,patios,cement/asphalt/gravel driveways,etc.If the proposed project exceeds 15%impervious surface,mitigation is required. <br /> If the impervious surface exceeds 30%,you will need to apply for a variance. NOTE: If you are only replacing existing legally <br /> built structures within the same footprint,no impervious surface calculations are needed.Land Services reserves the right to <br /> require a survey when there are disputes over this calculation. <br /> . . d . .1 • .. . 1511 1.1•-- .. • . .. - . . ..-- • .0 . tin_ ..• • - - .. <br /> • ' '. .. • . •Jose. structure on • - ... . . :. .: •• . . - <br /> Existing and proposed sanitary system and well locations including distances to existing and proposed structures <br /> Heights for all existing and proposed structures NOTE:Height is measured from lowest adjacent grade to the highest rocf,peak <br /> _. .. . '. / . : : - '_ •--_ --_ . .., -. .. mg;must show dimensions and proposed number of stalls <br /> - . . . ..-- •• • -• - . 6. I r.- -ns a .. • • •. ,• : Driveways must ave a c eare• a. . . - -- _ . <br /> ctPared h.i ht .,' A a� ugL fficient turn-around space fo i <br /> - d to be remove• or •isturbed <br /> s <br /> \tikr Construction plans shall be submitted with this application for all Commercial/Industrial related construction. <br /> onstruction plans shall show interior layout,exterior profiles and exterior heights. <br /> Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining <br /> walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the applicant. <br /> Page 2 of 5 <br /> • Burnett County, WI Land Use Application—Rev 12/2021 <br />