Laserfiche WebLink
PLOT PLAN REQUIREMENT <br /> A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to <br /> scale,in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing,if one is used.The plot plan drawing shall <br /> be on letter or legal size paper with North being at the top of the page. (Make sure all relevant items below are shown—check <br /> each relevant box): <br /> ❑ Property lines,road right-of-ways,and road centerlines including distances to property lines,road right-of-ways and road <br /> centerlines for all existing and proposed structures on the parcel <br /> ❑ Ordinary High Water Mark(OHWM)when existing,and dis ,• - o it fr.• all existing and proposed structures <br /> ❑ Provide Total Impervious Surface(IS) '_ entages including new existing ., d proposed development.This standard is only <br /> applicable if the proposed projec ' within 300'of the OHWM of any i ody of water. You only need to count the impervious <br /> surfaces that are partially or entir y within 300'of the OHWM o . •.. of water.To calculate,divide the total existing and <br /> proposed impervious surfaces i square feet by the total squ. - •otage of the parcel above the OHWM.Then multiply that number <br /> by 100 to get a percentage.Ex. , e:2,500 square __ IS within 300'of OHWM-43,560 square foot parcel x 100= 5.74% <br /> impervious surfaces(1 acre=43,560 square et .Impervious surfaces include but are not limited to:building roofs,sidewalks, <br /> decks,patios,cement/asphalt/gravel driveways,etc.If the proposed project exceeds 15%impervious surface,mitigation is required. <br /> If the impervious surface exceeds 30%,you will need to apply for a variance.NOTE:If you are only replacing existing legally <br /> built structures within the same footprint,no impervious surface calculations are needed.Land Services reserves the right to <br /> require a survey when there are disputes over this calculation. <br /> ❑ Floodplain and wetland areas/boundaries and distances to them from all existing and proposed structures <br /> U Existing and proposed structures on the parcel including all decks/porches/walkways/etc;must show dimensions for ALL items <br /> ❑ Existing and proposed sanitary system and well locations including distances to existing and proposed structures <br /> ❑ Heights for all existing and proposed structures NOTE:Height is measured from lowest adjacent grade to the highest roof peak <br /> ❑ (Commercial/Industrial Only)Existing and proposed parking;must show dimensions and proposed number of stalls <br /> ❑ Existing and proposed driveways;must show dimensions and width NOTE:Driveways must have a cleared width of 20 ft and a <br /> cleared height of 13 ft,and sufficient turn-around space for rescue services to utilize <br /> ❑ North arrow <br /> ❑ Vegetation proposed to be removed or disturbed <br /> U Location and extent of proposed filling/grading <br /> ❑ Location and type of erosion control measures <br /> ❑ Construction plans shall be submitted with this application for all Commercial/Industrial related construction. <br /> Construction plans shall show interior layout,exterior profiles and exterior heights. <br /> ❑ Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining <br /> walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> ❑ If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the applicant. <br /> Page 2 of 5 <br /> Burnett County,WI Land Use Application — Rev 12/2022 <br />