Laserfiche WebLink
PLOT PLAN REQUIREMENT' <br /> A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to <br /> scale, in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing, if one is used. The plot plan drawing shall <br /> be on letter or legal size paper with North being at the top of the page. (Make sure all relevant items below are shown—check <br /> each relevant box): <br /> Ll Property lines,road right-of-ways, and road centerlines including distances to property lines, road right-of-ways and road <br /> centerlines for all cxisting and proposed structures on the parcel <br /> J Ordinary I ligh Water Mark(011WM) when existing, and distances to it from all existing and proposed structures <br /> ❑ Provide Total Impervious Surface(IS) Percentages including new existing and proposed development. This standard is only <br /> applicable if the proposed project is within 300' of the Of IWM of any body of water. You only need to count the impervious <br /> surfaces that are partially or entirely within 300` of the Of IWM of a body of water. To calculate,divide the total existing and <br /> proposed impervious surfaces in square feet by the total square footage of'the parcel above the OI IWM. "then multiply that number <br /> by 100 to get a percenta,;c. I"Aample: 2,500 square fret of'IS within a00' of'OH WM 43,560 square foot parcel - 100 5.74% <br /> impervious surfaces(1 acre 43,560 square Icet). Impervious surfaces include but are not limited to: building roofs,sidewalks, <br /> decks, patios,cement/asphalt/gravel driveways, etc. If the proposed project exceeds 15% impervious surface, mitigation is required. <br /> If the impervious surface exceeds 30%,you will need to apply for a variance. NOTE: If you are only replacing existing legally <br /> built structures within the same footprint, no impervious surface calculations are needed. Land Services reserves the right to <br /> require a survey when there are disputes over this calculation. <br /> u Floodplain and wetland areas/boundaries and distances to thern from all existing and proposed structures <br /> J Existing and proposed structures on the parcel including,all decks'porchcs walkways etc; must show dimensions for ALI. items <br /> J Existing and proposed sanitary system and well locations including distances to existing and proposed structures <br /> J I Icights for all existing and proposed structures NOTE: I leight is measured from lowest adjacent grade to the highest roof peak <br /> ❑ (Commercial/Industrial Only) Existing and proposed parking; must show dimensions and proposed number of stalls <br /> ❑ Existing and proposed driveways: must show dimensions and width NOTF: I)rivcways must have a cleared width of 2.0 ft and a <br /> cleared height of' 13 ft, and sufficient turn-arOunll space for rescue scrviccs to uti!iic <br /> J North arrow <br /> Vegetation proposed to be removed or dj/urbed <br /> u Location and extent of proposed fillin6//grading <br /> ❑ Location and type of erosion control measures <br /> J Construction plans shall be submitted with this application for all Commercial/Industrial related construction. <br /> Construction plans shall show interior layout, exterior profiles and exterior heights. <br /> J Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> County staff will do an onsite visit to verify site conditions. If all proposed structures (including decks, patios, retaining <br /> walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> ❑ If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the applicant. <br /> Page 2 of 4 <br /> Burnett County, WI Land Usc Application — Rev 1/2019 <br />