Laserfiche WebLink
A plot plan drawing is required to be submitted along with this application. The plot plan drawing shall either be drawn to <br /> scale,in feet,or be FULLY dimensioned in feet. Please note the scale on the drawing,if one is used.The plot plan drawing shall <br /> be on letter or legal size paper with North being at the top of the page. (Make sure all relevant items below are shown—check <br /> each relevant box): <br /> Property lines,road right-of-ways,and road centerlines including distances to property lines,road right-of-ways and road <br /> / \ centerlines for all existing and proposed structures on the parcel <br /> Ordinary High Water Mark(OHWM)when existin d distances to it from all existing and proposed structures <br /> ❑ Provide Total Impervious Surface(IS)P to es including new existing and p oposed development.This.standard is only <br /> applicable if the proposed pro' within 300' of the OHWM of any body of water. You only„need to count the impervious <br /> surfaces that are partially o ely within 300'of the OHWM of a-body of water.To calcul e divide the total existing and,----- <br /> proposed impervious aces in square feet by the total square footage of the parcel abo : +.e OHWM.Then multipl number <br /> by 100 to get a r- -ntage.Example: 2,500 square feetof IS within 300'of OHWM . '3,560 square foot parte 00= 5.74% <br /> impervious : aces(1 acre=43,560 square feet)Impervious surfaces include b are not limited to:building roofs,sidewalks, <br /> decks, ..tios,cement/asphalt/gravel drivewa ;etc.If the proposed project ex•--ds 15%impervious,rface,mitigation is required. <br /> If .- impervious surface exceeds 30%,yo will need to apply for a varian .NOTE:If you are oy replacing existing legally <br /> ilt structures within the same footp ' t,no impervious surface calc :tions are needed. Land Services reserves the right to <br /> require a survey when there are disp es over this calculation. :r' <br /> ❑ • weitand areas/boun 'dames and stances to diem from all existingan`ffpropose s3 struciilt s '- <br /> Existing and proposed structures on the parcel including all decks/porches/walkways/etc;must show dimensions for ALL items <br /> /‘ Existing and proposed sanitary system and well locations including distances to existing and proposed structures <br /> Heights for all existing and proposed structures NOTE:Height is measured from lowest adjacent grade to the highest roof peak <br /> ❑ (Commercial/Industrial Only)Existing and proposed parking;must show dimensions and proposed number of stalls <br /> ...-Ni Existing and proposed driveways;must show dimensions and width NOTE:Driveways must have a cleared width of 20 ft and a <br /> 'N cleared height of 13 ft,and sufficient turn-around space for rescue services to utilize <br /> North arrow <br /> Vegetation proposed to be removed or disturbed <br /> Location and extent of proposed filling/grading <br /> ) Location and type of erosion control measures <br /> Construction plans shall be submitted with this application for all Commercial/Industrial related construction. <br /> III Construction plans shall show interior layout,exterior profiles and exterior heights. <br /> ,t‘ Proposed building/structure locations must be staked prior to submitting this application to the Land Services Department. <br /> I County staff will do an onsite visit to verify site conditions. If all proposed structures(including decks,patios,retaining <br /> walls,etc)are not staked upon County staff visit,the permit may not be approved and may be returned to the applicant. <br /> If all existing structures on the parcel are not shown and dimensioned on the plot plan drawing,the permit may not be <br /> issued and may be returned to the applicant. <br /> Page 2 of 4 <br /> Burnett County,WI Land Use Application—Rev 6/2020 <br />